For modeling purposes, Bondo’s density lets it stick well to pieces of wood, foam, and carbon fiber. These materials aren’t affected by the polyester resin, so they allow the Bondo to be applied without surface deterioration.

Table of Contents

Can you use Bondo over foam?

Super Moderator. Foam will hold/trap moisture and worsen the situation over time. Use strips of metal (perforated strapping would do) and fasten a metal sheet to the matal or fiberglass over it (two applications of fiberglass should do) and then use bondo.

What surfaces does Bondo stick to?

In addition to its uses on vehicle exteriors and other metal surfaces it is also a suitable repair option for wood, fiberglass and concrete. For repair of any fiberglass material for home, automotive or marine application, look to Bondo Products.

Does Bondo stick to EVA foam?

So can you use Bondo on EVA Foam? In short, yes you can. You only have to lightly sand the area of the EVA Foam where you want to apply Bondo so that the Bondo has something to grip on to. Then Mix your hardener with the right amount of Bondo and simply apply it to the surface of your EVA foam.

Will bondo stick to polyurethane?

Yes you are right. Regular body filler will not adhere to plastic bumpers. They make a flowable body filler called “glazing” or “poly/polyester” putty. It will tell you right on the back that it will stick to polyurethane.

👉 For more insights, check out this resource.

Will bondo stick to duct tape?

Duct tape is coated with a “oily” substance to help with it being used it the weather. The “bondo” will lay down on the tape and help smooth out the tapes texture. But it wont take much for the “bondo” to come off of the duct tape,especially if it has some help from a fall or bump.

Can you fill over expanding foam?

It shoots liquid foam deep into cavities, creating a long lasting seal, which insulates against heat, sound and moisture. Suitable for inside or out, it can be easily trimmed and sanded ready to be painted, filled or plastered. … Can be painted over, filled or plastered.

👉 Discover more in this in-depth guide.

Why is Bondo bad?

Unfortunately, filling compounds such as Bondo also present some drawbacks. Fillers like Bondo can crack if they are mixed too thickly, harming rather than improving the look of the car. Additionally, there’s a risk of discoloration and poor long-term wear when you use a dent repair filler like Bondo.

Does Bondo harden without hardener?

Without it the bondo won’t get hard. Put a small piece of bondo on a board and run a line of hardener from end to end. It will take about five minutes to mix it up and apply it.

How long until you can sand Bondo?

A Lot. There are two schools of thought on when to sand filler. If you are doing general bodywork, leveling wavy panels, fixing small dings, etc, then wait until the filler is fully cured, about 20-30 minutes.

Article first time published on

Will body filler stick to a plastic bumper?

Plastic repair materials should be used when performing repairs on bumper covers. … All these products are designed to move with the bumper so the material does not crack. Body filler is also not designed to adhere to a plastic surface the way that it adheres to metal.

Can you Bondo over urethane primer?

As long as the filler is fine enough to get into the scratches in the primer or paint and the primer or paint that you’re putting it on is a good quality urethane that is well attached to the surface then you’re probably ok.

Will mice eat through expanding foam?

RODENT RESISTANT EXPANDING FOAM Filling the cracks and voids with the polyurethane foam acts as a rodent barrier, as mice and other rodents aren’t able to chew through spray foam insulation.

How big a hole can expanding foam fill?

That leaves the mid-sized holes, from 1 to 5 inches in diameter, such as the one a doorknob would make. One of the most effective materials you can use to fill them is polyurethane spray foam.

What grit sandpaper do I use for Bondo?

First step: Prep the Surface Make sure to sand outside of the repair area as Bondo will need to be spread and applied wider than the damaged area. (36-grit to 220-grit should do the trick for body filler application). AutoBodyNow.com sells a vast assortment of sandpapers and sanders to complete this step.

Is Bondo hard to sand?

Once the Bondo cures, it’s time to sand. Power sanders are OK to break the surface and knock down any high spots, but hand sanding with the body contour is the best way forward. … The lightweight Bondo Gold is far easier to sand than the heavier type, so consider using the good stuff on the way out.

Do you have to use hardener with Bondo?

(Bondo comes with a tube of hardener.) If you add too much hardener, the mixture will gel too quickly. If you add too little, it increases the amount of time for it to cure, and if you don’t add enough it will never cure.

Can you thin filler?

Thin it with plastic honey(4%) or fiberglass resin. Don’t use too much honey cause it will interfere with adhesion. If you put too much add more hardener. Mix honey/resin with filler before adding hardener.

Can you thin down car body filler?

Over time body fillers can become hard and difficult to work with, or you may want to thin out your filler to apply a skim coat over a large area. Mark Simpson explains why many body fillers get firm over time and how thinning bondo can return it to a more workable condition.

How do you harden foam?

White EPS Styrofoam can be hard coated with liquid polyurethane. Keep your Styrofoam props, cosplay outfits and other projects protected with a hard-surface coating. You don’t need to rely on messy fiberglass resin to harden your Styrofoam. Simply use a two-part liquid polyurethane hard-coat system.

How do you seal EVA Foam paint?

There are several ways to seal EVA Foam (depending on the kind of project) but the most reliable way to Seal Foam is using Plasti Dip. Then the Foam can be painted with Acrylics, Spray Paint with an Airbrush, and more. After painting, you can choose to Seal your Project with a Mat Sealer, Epoxy Resin or a Varnish.

Can you fiberglass over EVA Foam?

Fiberglass is a very strong and durable construction material, used for many different applications. … Fiberglass will bond to almost any surface, including wood, foam, metal and even plastic.

Can you sand down foam?

If the Foam has a medium to high-Density, then the Foam can be easily sanded with regular Sanding Paper. If the Foam is a low-density Foam, then a Rotary Tool with a stone sanding bit can be used.

What paint can be used on craft foam?

Can You Paint Craft Foam Board? The best kind of paint for foam core is acrylic paint because it doesn’t require solvents like oil paint. The acrylic is fast-drying, durable, and adheres to most surfaces well.

Will filler go off without hardener?

The resin which is included in wood filler prevents the hardening by itself without hardener. Once the resin will eventually run out and atmospheric oxygen will participate to harden the wood filler even without the hardener.

How long can Bondo be left unpainted?

Between life and work, the longest time period the bondo would go Unpainted would be about 2-3 weeks.