Under stucco, you can use asphalt felt or two layers of Grade-D building paper, commonly used on the West Coast. Both asphalt felt and Grade D paper will block liquid water but allow water vapor to pass through.

Table of Contents

What kind of paper goes behind stucco?

60 Minute Stucco Paper (Two-Ply Super Jumbo Tex Water Resistive Barrier) is the flagship product of the Jumbo Tex line – a product that has set the industry standard for effectiveness and durability as a weather resistive barrier behind all major exterior wall claddings.

Can Tyvek be used under stucco?

Yes, DuPont™ Tyvek® WB can be used under any façade, including brick, stucco, vinyl, cedar siding, metal, and stone. Proper installation under each façade is essential to ensure Tyvek® provides the maximum level of air infiltration resistance and bulk water holdout.

What do you put under stucco?

Sheathing is basically the “backing material” that can be found underneath the various layers of stucco that form the backing of residential and commercial buildings. They can be made out of wood, cement, gypsum, fiberglass and other materials.

Do you need house wrap under stucco?

Stucco is actually a porous material and is designed to allow the absorption of water. The building paper or Tyvek (water-resistive barrier) acts as a drainage plane, and as the stucco dries, water flows down the building paper and weeps out the bottom of the stucco. … No drainage means big trouble–Rot City”.

👉 For more insights, check out this resource.

What is a building paper?

Building paper and housewraps (collectively called sheathing membranes, vapour permeable sheathing membranes, or weather resistive barriers) are widely specified to control moisture movement in walls and roofs. Fundamentally, these products act as capillary breaks and drainage planes, not as waterproofing.

How many layers of paper do I need for stucco?

Figure 1: Two Layers of Building Paper—The two layers of building paper are significant in the performance of hardcoat stucco assemblies. The outer layer of building paper acts as bond break between the stucco and the inner layer of building paper permitting modest drainage of water between the two layers.

👉 Discover more in this in-depth guide.

How do you put screws in stucco?

  1. Step 1: Mark the area of the screw placement. …
  2. Step 2: Make a pilot hole with a drill. …
  3. Step 3: Optional, put caulk in the hole. …
  4. Step 4: Optional, place a screw anchor in the hole. …
  5. Step 5: Drive in the stucco screw.

Can you put stucco on plywood?

Stucco is one of the oldest building materials in continuous use. But more often than not, stucco is applied today to homes which are made of standard wood construction, covered with plywood sheathing. … Either softwood construction-grade exterior plywood can be used or OSB .

What is Type D building paper?

Grade A – High water-vapor resistance. Grade B – Moderate water-vapor resistance. Grade C – Water resistant. Grade D – Water-vapor permeable.

Article first time published on

Can tar paper be used as a vapor barrier?

Tar paper can be used as an effective vapor barrier, but other materials may work better, depending on the conditions of your home and your climate. … In old construction, some homes contain tar paper, but modern construction may use other materials since tar paper tends to retain water and damage easily.

Do you tape the bottom of Tyvek?

Yes, the DuPont Tyvek HomeWrap should be overlaid from 6″ to 12″ and should be seamed up with 3″ tape. … Also, make sure that the DuPont Tyvek HomeWrap is installed similar to shingles on a roof so that the water will not run behind the bottom layer.

Do you need Tyvek under stucco?

Yes, DuPont™ Tyvek® WB can be used under any façade, including brick, stucco, vinyl, cedar siding, metal, and stone. Proper installation under each façade is essential to ensure Tyvek® provides the maximum level of air infiltration resistance and bulk water holdout.

Can you put tar paper over Tyvek?

Tyvek over Tar Paper: We have already established that there is no issues with moisture sandwiches, what about using Tyvek over a different item like Tar Paper? As long as the tar paper is in real good shape, in most cases you would be fine, as long as neither product gets wet.

What is lath for stucco?

Lath is simply the first step in the stucco process. It consists of water resistant paper, (sometimes eps foam) wire and other metal components that make up the essential “framework” for the cement to be adhered to. It attaches to the substrate and is the structure for the following coats.

Can you put house wrap over stucco?

In short — yes! A stucco exterior can be covered with siding for an updated look. However, because of the process that must be done to cover stucco properly, this project should really only be completed by a professional.

What kind of wire is used for stucco?

17 Gauge Wire (Three Coat Stucco Wire): This particular wire is commonly used in the three coat stucco system and is a fairly strong kind of wire. It is furred, which means that it sticks off of the wall a little bit (about a quarter inch or so) so that the stucco mix can “key” in behind it.

What's the difference between 10 minute building paper and 60 minute building paper?

10 Minute Paper: 10 minute paper is the thinnest type of stucco paper used nowadays and is probably the easiest to use. … 60 Minute Paper: 60 minute paper is one of the thickest papers available and if using a two ply roll, it is very tear resistant and adds some serious water protection over a 10 minute paper.

What is the brown coat in stucco?

The brown coat is applied over the scratch coat to prepare the plaster base for the finish coat application. The three coats consist of two base coats and one finish coat. The first base coat is called a scratch coat, the second is called a brown coat. In two coat work, there is a single base coat and a finish coat.

What paper is used with building houses?

Building paper is thick tar paper that is frequently used between exterior wall sheathing and masonry / stucco siding. Building paper is also used for temporary home weather protection. Building paper comes in rolls of various widths, lengths and weights.

How thick is building paper?

Roofing Paper Thickness The most commonly used felts are #15 and #30, with weights of 8 and 20 pounds per 100 square feet, respectively. The most commonly used is #15, which comes in rolls 3 feet wide, is 144-feet long and covers approximately four squares per roll, or approximately 400 feet of roof.

Can I use felt paper as house wrap?

House wrap and felt paper, when properly installed and undamaged, are both weather resistant barriers (WRB) that create permeable and water- and air-resistant exterior walls. The main advantage of house wrap, over felt paper, is the superior strength and durability of house wrap.

Why is stucco bad?

Keep in mind that stucco is porous, so unlike vinyl and other siding materials, it absorbs moisture. The elements can therefore wreak havoc on your stucco, and as a result, your home may develop unsightly dark spots. It may even grow mold, which is very noticeable on your home’s exterior.

How do you prepare plywood for stucco?

Apply two layers of grade D building paper or asphalt felt to the plywood siding. Follow with the three-dimensional drainage mat and two more layers of paper or felt. Secure stucco mesh to your walls and then apply your layers of stucco for a watertight finish.

Can I screw directly into stucco?

Can I Screw Into Stucco? The answer to that question is, yes you can screw into stucco if you have the right type of screw, a screw gun and a drill bit. It is easier to drill into the stucco first and then drive the screw in with either a drill or a screwdriver/nut driver.

How do you secure something to stucco?

Attach a masonry bit to a drill and go into the stucco, just a little longer than the length of the anchor. Fill the hole with silicone caulk and put the anchor into the hole. Hammer it gently until it’s flush with the wall. Put corrosion-resistant screws into the anchor(s).

Do you need a hammer drill for stucco?

Can I Drill Through Stucco? To answer the question, yes you can drill through stucco with the right drill bit and proper drill. Masonry type of bits with carbide or diamond tips are the go to bits for stucco and having a hammer drill will greatly help with larger holes.

Is Tyvek grade D building paper?

Grade D paper By helping to seal the building envelope, Tyvek® StuccoWrap® helps protect buildings against bulk water intrusion and air-transported moisture, two factors that can lead to mold and wood damage if water accumulates in the wall cavity.

What is Grade B building paper?

GRADE B: A building paper classified as a moderate water/vapor resistant material. According to the UBC Standard 14-1, it must have a water resistance of not less than 16 hours. … TSIB also recommends the use of Grade “D” (or equivalent) building paper when exterior gypsum sheathing is the substrate.

What is tar paper used for?

Tar paper is a heavy-duty paper used in construction. Tar paper is made by impregnating paper or fiberglass mat with tar, producing a waterproof material useful for roof construction.

Which is better tar paper or Tyvek?

Tyvek offers more permeability but less longevity, and you find it near the exterior siding. Tar paper withstands high moisture levels, but it can crack in freezing temperatures. That’s why you usually find it on the interior walls.